Siemens X-Ray Equipment Servicer's Technical Forum
November 23, 2017, 04:26:19 AM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
News: The New (and improved) Siemens X-Ray Equipment Servicer's Technical Forum. More features, more information and more help for Siemens Imaging Equipment service providers and support persons.
 
   Home   Help Search Login Register  
Pages: [1]
  Print  
Author Topic: SSW version D200  (Read 1266 times)
sestos
Newbie
*
Posts: 9


« on: February 20, 2015, 09:22:15 AM »

hello I need the software configuration of D200 generator Polidoros lx 50 multix table. fw version D200 VC00B
Logged
vesper
Global Moderator
Hero Member
*****
Posts: 2887



« Reply #1 on: February 21, 2015, 11:40:15 PM »

@sestos:
I am not sure what you are asking exactly.
In case you mean that you want the service software for the Polydoros LX, then you need to tell me what software version is loaded to your generator (the firmware version does not show this...)
Logged
sestos
Newbie
*
Posts: 9


« Reply #2 on: February 22, 2015, 02:29:35 AM »

vesper friendly, thanks for the reply, I will try to explain.
I had to replace the card 200 d of a generator Polidoros lx 50 to which is attached a table multix. Now unfortunately I only back up the site. I could use a sw version for d200 compatible with my back up.homprovato to load version vc 00s but not good. where can I check the version of sw generator?
Logged
vesper
Global Moderator
Hero Member
*****
Posts: 2887



« Reply #3 on: February 22, 2015, 05:52:52 AM »

If you replaced D200 board, then you need to load to this D200 the software that was loaded in the old one (defective) to have the generator back in order.

In the photo you sent me (file:"20150220_180528.jpg"), I can see that the XCU software version is VC00S and the XCS software version is VF00B. This photo comes from the "new" D200 or from the "old" one?
Logged
sestos
Newbie
*
Posts: 9


« Reply #4 on: February 28, 2015, 12:12:13 AM »

is this picture and what is currently installed in the generator, unfortunately I have the old configuration xcu.thanks for the reply, I hope we can find a solution, greetings
Logged
vesper
Global Moderator
Hero Member
*****
Posts: 2887



« Reply #5 on: March 01, 2015, 04:01:16 AM »

Since the picture comes from the "new" D200 board, there is no way to find out the old software versions of the unit.
The "new" D200 seems to be coming from a lithotripter generator, so it needs a total erase of its configuration before anything else.

I will send in your email, the XCS-SSW version VE02D which is the most common version in simple x-ray generators and the XCU firmware version VC00M (the two of them are compatible with each other). You should use these the VE02D XCS service software to download the VC00M firmware to D200 and then (after an erase of any previous configuration...) configure from the beginning the Site Structure of the generator and perform all tube adjustments.

Logged
sestos
Newbie
*
Posts: 9


« Reply #6 on: March 01, 2015, 05:48:07 AM »

thanks, if you can send me email with versions sww?
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
moneypit